THE CUT BUDDY

·

NOV 14, 2026

HOW TO SHAVE YOUR HEAD BALD IN 6 EASY STEPS (WITHOUT IRRITATION)

Making the step to bald — without the irritation

Going from a horseshoe of hair to fully bald is a big step, and the difference between a shave that looks great and one that leaves you covered in bumps is almost always the routine, not the razor. In this video, Josh — CEO of The Cut Buddy — walks through the exact six-step process he uses to shave his head smooth without irritation, and shows every product along the way.

Whether you're newly bald or you've been shaving for years and still fighting razor bumps, these six steps are worth building into your routine.

Step 1: Trim the hair down first

Start by trimming everything down to stubble with a trimmer. Go against the grain — upward, not down with the direction your hair grows — and don't try to be fancy. The point of this step is simply to clear the canvas so the bald shaver has an easier time in step 5. Get the 5 o'clock shadow and anything longer than a millimeter down to skin level.

Josh getting ready to shave his head bald
Josh gets ready to take his horseshoe down to bald.

Step 2: Exfoliate — never skip this

Exfoliation is the step Josh calls extremely important, and it's the one most people skip. Using an exfoliating brush (the Wizker brush in the video), work it over your head in circular patterns to sand away dead skin, dandruff, dirt, and grime. Why it matters: if that buildup is still on your scalp when you shave, you're plowing it straight into your pores — and that's what causes irritation and ingrown hairs. This matters most if you have coarse hair.

How do you know you exfoliated properly? Your head will look dusty and ashy, and when you hold up the brush, you'll see everything it picked up. That's the sign it worked.

Step 3: Wash your head

Head to the shower and wash your head before any blade touches it. You don't want the dust and debris from exfoliating sitting on your scalp when you start shaving. Work the wash into all the pores of your scalp, and focus on the horseshoe area — that's where most of your shaving happens. Josh also applies it to his face in the video, and uses an exfoliation attachment to massage it in for a clean, even base.

Step 4: Apply foaming shaving cream

Now apply shaving cream — and Josh's pick is a foaming shaving cream. It covers the full surface area, acts like a conditioner, and softens the hair so it shaves off easier. You don't need much: a small amount goes a long way. Let it sit on your head for 30 seconds to a minute before shaving. That pause gives the cream time to soften the hair and gives its antibacterial properties a chance to work.

Josh with shaving cream on his head in the shower
Shaving cream applied in the shower before the Bald Buddy shaver.

Step 5: Heat, then shave

Before the blade goes on, open your pores with heat. Run the shower hot and mix the water into the shaving cream to build a lather. Hot temperatures open the pores; shaving with closed pores means stiffer hair, more friction, and a much higher chance of razor burn and ingrown hairs.

Then shave with the Bald Buddy shaver, starting with general circles and moving to smaller circles, working only the area you trimmed down. The flexible heads contour to your head, and the ergonomic handle makes it easy to switch to your weak hand. Work fast — as Josh puts it, every pass of a blade wounds a thin layer of skin, so the fewer passes, the better. Don't forget the forehead area where your hairline used to meet your forehead, so the skin blends evenly.

The back of the neck gets special treatment, because it's where most people irritate. Two options: use only a trimmer on the back of your neck, or use the shaver with short straight strokes — no circles. Keep circling back there and, in Josh's words, it'll look like Rice Krispies no matter what.

If the shaver starts bogging down with cream and hair, rinse it under the shower or use the cleaning cup the Bald Buddy comes with, then keep going. The horseshoe is the thickest, most stubborn hair — that's where most of your effort goes. The top of your head is the easy part.

Step 6: Post-shave care — the most important step after exfoliation

You're not done when the shaving stops. Post-shave care is what decides whether tomorrow brings a smooth head or a breakout.

Josh smiling after a smooth bald shave
The smooth, bump-free result of the six-step routine.

Dry by dabbing, not rubbing. Grab a microfiber towel, or an old towel whose fibers have long since washed out — not a fresh fibrous one. You just removed all the fibers, grime, and dust from your head; rubbing with a rough towel puts irritation right back onto freshly wounded skin. Dab gently. Rubbing a fresh shave with a towel, Josh says, is like scratching a wound with sandpaper.

Check your work. If you missed a spot, don't re-shave the whole area with the shaver. Just take a trimmer and knock the strays down — nobody will notice, and your skin will thank you.

Apply a post-shave treatment spray. You want something alcohol-based or with hypochlorous acid — Josh's spray also includes salicylic acid and tea tree. It kills germs and makes the skin pucker, closing the pores back up so they stop accepting bacteria. A few sprays is enough. The first application may sting — that's normal on freshly shaved skin. Josh's test: spray a second layer right after, and if it doesn't burn, your skin is in good shape.

Follow with a balm or lotion. Two options, same job: Bump Buddy is a potent cream — a light layer along the shaved areas is all you need. The post-shave butter is thicker, comes in a big jar, and works best when you have time to let it soak in (overnight is ideal). Apply the butter generously, the way you'd apply diaper rash cream — it needs a real layer to be effective.

Rag up for an hour. Finish by putting on a durag or satin head cover for about an hour. Think of it as a band-aid: it protects your head while the skin heals, so a hat or pillow isn't rubbing against it. Josh wears his with the flap down to protect the neck too, then pops it off when he's ready for the day.

The result

Six steps: trim, exfoliate, wash, foaming cream, heat and shave, post-shave care. Follow them in order and you go from horseshoe to smooth, bump-free bald — the same routine Josh uses himself.

Watch the full routine, start to finish: How to Shave Your Head Bald in 6 Easy Steps

Products mentioned in the video

Related News